Doc updates
This commit is contained in:
Pontus Borg
parent
920420ccf0
commit
1f9e16b5d0
72
README.md
72
README.md
@ -27,6 +27,13 @@ If you are interesting in helping out, testing or eventually using this board fe
|
||||
* [CAN bus](doc/canbus.md)
|
||||
* [Prototype versions of the board](doc/versions.md)
|
||||
|
||||
---
|
||||
Buy it at:
|
||||
|
||||
* Lukes Lab: https://www.lukeslab.online/general-3d-printer-parts/klipper-toolboard-can-huvud-v0-5
|
||||
* Tindie: https://www.tindie.com/products/huvud/huvud-3d-printer-hotend-control-board/
|
||||
|
||||
|
||||
|
||||
---
|
||||
|
||||
@ -36,69 +43,4 @@ https://hackaday.io/project/174429-huvud-a-3d-printer-tool-head-controller-board
|
||||
---
|
||||
|
||||
|
||||
## 2020-05-18:
|
||||
|
||||
First prototype production run is done.
|
||||
|
||||
|
||||
|
||||
They work!
|
||||
|
||||
---
|
||||
## 2020-05-29:
|
||||
|
||||
|
||||
|
||||
After a lot of software work and many hours of testing I can report that everything actually works as intended (except one resistor that was a 10k insteadof 1k)
|
||||
|
||||
* The thermistor input gives a very low noise signal, even at high temperatures.
|
||||
* Endstop works
|
||||
* All mosfet outputs works with reasonable loads (2A at 24V). I do not have a dummy load for high load testing, but a heater on the FAN connectors and a hotbed to the heater connector...
|
||||
* The thermals of the TMC2209 seems ok. With no cooling fins or active cooling it reaches 60C (top and bottom) when mounted close to a hot stepper. I should test with a larger stepper (>1.5A) in a hotter environment to see when the TMC shuts down. I am considering a different fab that allows thicker copper layers for better heat spead, and better power margins.
|
||||
* The CAN bus works good after some software work. It should work fine with up to 8 nodes on each bus, possibly more. I have run 4 boards on the same bus, each with one stepper, simulating a complete 3D printer.
|
||||
|
||||
It is possible to fit different connectors for most functions. It is designed for mostly angled JST-XH or screw terminals but it's possible to fit straight connectors or other 2.54mm for most functions. JLCPCB do not mount through holes so the boards come without connectors.
|
||||
For a larger (>30) production run the boards would have to be panellized, which looks like a non-trivial task with KiCAD. If anyone has experience and wants to help ...
|
||||
|
||||
---
|
||||
## 2020-06-10:
|
||||
|
||||
Version 0.4 is almost complete.
|
||||
|
||||
* It has an on-board 3.3V regulator replacing the external board. (Quite a challenge for an old SW engineer using JLCPCB's very limited selection of components)
|
||||
* Thermistor connector moved down next to the fan/heater connectors
|
||||
* Lower profile capacitor for the stepper driver, it was very tall.
|
||||
* Debug header moved and extended. BOOT1 exposed.
|
||||
* Serial pins removed, not very useful anyway
|
||||
* Fan/heater connectors tweaked to be able to fit JST XH, screw terminals or Molex KK connectors.
|
||||
* Added a micro-USB connector for easier flashing and possibly other features. The board is not powered from USB.
|
||||
* Switched to an STM32F103. Mainly to allow for a proper bootloader and flashing over USB. Or even over CAN if I develop a custom bootloader. With many boards it would be very nice to be able to bulk flash them all at once over CAN.
|
||||
|
||||
|
||||
I have done thermal stress testing of the board. It can run a big stepper at 1.5A, board attached very close to the hot stepper with no forced airflow and 25C ambient. The driver reaches 90C (measured with a probe) but does not shut down due to overheating. The entire board heats up as designed to act as a heatsink, most inner and outer copper layers are groundplanes to spread the heat.
|
||||
|
||||
I'll very soon order another 20-30 board to send out to brave beta testers.
|
||||
|
||||
---
|
||||
## 2020-06-24
|
||||
|
||||
Ready to manufacture some more prototypes
|
||||
|
||||
Among many small tweaks the heater mosfet is changed to a different one with better Rds at 3.3V Vgs. If I limit the board to 24V and a 40W heater it could use the same small mosfet as for the fans.
|
||||
|
||||
Unfortunately JLCPCB are out of TMC2209 so I'll have to find a different prototype house that has them available. Perhaps one with 2oz outer copper layers for better thermals.
|
||||
|
||||
CAN bus is surprisingly robust. I have tested it through a 50m roll of ethernat cable, various sketchy test setups with star networks, breadboards, close to EMC sources etc. It always works. The Bosch engineers did a good job almost 40 years ago.
|
||||
|
||||
---
|
||||
|
||||
# Can Hat
|
||||
|
||||
|
||||
As a sub project to this board I have developed a little power and CAN distribution board combined with an MCP2515 CAN bus controller in the form of a Raspberry Pi Hat. It is a very simple little board but has turned out to be very valuable.
|
||||
|
||||
With some more thought put into it I think it will be a good complement to the Huvud tool board.
|
||||
|
||||
---
|
||||
|
||||
|
||||
|
||||
BIN
doc/canable.jpg
Normal file
BIN
doc/canable.jpg
Normal file
Binary file not shown.
|
After Width: | Height: | Size: 130 KiB |
Loading…
x
Reference in New Issue
Block a user