rp2040_projects/i2c/oled_i2c/oled_i2c.c

/**
 * Copyright (c) 2021 Raspberry Pi (Trading) Ltd.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#include <stdio.h>
#include <string.h>
#include <stdlib.h>
#include "pico/stdlib.h"
#include "pico/binary_info.h"
#include "hardware/i2c.h"
#include "raspberry26x32.h"

/* Example code to talk to an SSD1306-based OLED display

   NOTE: Ensure the device is capable of being driven at 3.3v NOT 5v. The Pico
   GPIO (and therefore I2C) cannot be used at 5v.

   You will need to use a level shifter on the I2C lines if you want to run the
   board at 5v.

   Connections on Raspberry Pi Pico board, other boards may vary.

   GPIO PICO_DEFAULT_I2C_SDA_PIN (on Pico this is GP4 (pin 6)) -> SDA on display
   board
   GPIO PICO_DEFAULT_I2C_SCK_PIN (on Pico this is GP5 (pin 7)) -> SCL on
   display board
   3.3v (pin 36) -> VCC on display board
   GND (pin 38)  -> GND on display board
*/

// commands (see datasheet)
#define OLED_SET_CONTRAST _u(0x81)
#define OLED_SET_ENTIRE_ON _u(0xA4)
#define OLED_SET_NORM_INV _u(0xA6)
#define OLED_SET_DISP _u(0xAE)
#define OLED_SET_MEM_ADDR _u(0x20)
#define OLED_SET_COL_ADDR _u(0x21)
#define OLED_SET_PAGE_ADDR _u(0x22)
#define OLED_SET_DISP_START_LINE _u(0x40)
#define OLED_SET_SEG_REMAP _u(0xA0)
#define OLED_SET_MUX_RATIO _u(0xA8)
#define OLED_SET_COM_OUT_DIR _u(0xC0)
#define OLED_SET_DISP_OFFSET _u(0xD3)
#define OLED_SET_COM_PIN_CFG _u(0xDA)
#define OLED_SET_DISP_CLK_DIV _u(0xD5)
#define OLED_SET_PRECHARGE _u(0xD9)
#define OLED_SET_VCOM_DESEL _u(0xDB)
#define OLED_SET_CHARGE_PUMP _u(0x8D)
#define OLED_SET_HORIZ_SCROLL _u(0x26)
#define OLED_SET_SCROLL _u(0x2E)

#define OLED_ADDR _u(0x3C)
#define OLED_HEIGHT _u(32)
#define OLED_WIDTH _u(128)
#define OLED_PAGE_HEIGHT _u(8)
#define OLED_NUM_PAGES OLED_HEIGHT / OLED_PAGE_HEIGHT
#define OLED_BUF_LEN (OLED_NUM_PAGES * OLED_WIDTH)

#define OLED_WRITE_MODE _u(0xFE)
#define OLED_READ_MODE _u(0xFF)

struct render_area {
    uint8_t start_col;
    uint8_t end_col;
    uint8_t start_page;
    uint8_t end_page;

    int buflen;
};

void fill(uint8_t buf[], uint8_t fill) {
    // fill entire buffer with the same byte
    for (int i = 0; i < OLED_BUF_LEN; i++) {
        buf[i] = fill;
    }
};

void fill_page(uint8_t *buf, uint8_t fill, uint8_t page) {
    // fill entire page with the same byte
    memset(buf + (page * OLED_WIDTH), fill, OLED_WIDTH);
};

// convenience methods for printing out a buffer to be rendered
// mostly useful for debugging images, patterns, etc

void print_buf_page(uint8_t buf[], uint8_t page) {
    // prints one page of a full length (128x4) buffer
    for (int j = 0; j < OLED_PAGE_HEIGHT; j++) {
        for (int k = 0; k < OLED_WIDTH; k++) {
            printf("%u", (buf[page * OLED_WIDTH + k] >> j) & 0x01);
        }
        printf("\n");
    }
}

void print_buf_pages(uint8_t buf[]) {
    // prints all pages of a full length buffer
    for (int i = 0; i < OLED_NUM_PAGES; i++) {
        printf("--page %d--\n", i);
        print_buf_page(buf, i);
    }
}

void print_buf_area(uint8_t *buf, struct render_area *area) {
    // print a render area of generic size
    int area_width = area->end_col - area->start_col + 1;
    int area_height = area->end_page - area->start_page + 1; // in pages, not pixels
    for (int i = 0; i < area_height; i++) {
        for (int j = 0; j < OLED_PAGE_HEIGHT; j++) {
            for (int k = 0; k < area_width; k++) {
                printf("%u", (buf[i * area_width + k] >> j) & 0x01);
            }
            printf("\n");
        }
    }
}

void calc_render_area_buflen(struct render_area *area) {
    // calculate how long the flattened buffer will be for a render area
    area->buflen = (area->end_col - area->start_col + 1) * (area->end_page - area->start_page + 1);
}

#ifdef i2c_default

void oled_send_cmd(uint8_t cmd) {
    // I2C write process expects a control byte followed by data
    // this "data" can be a command or data to follow up a command

    // Co = 1, D/C = 0 => the driver expects a command
    uint8_t buf[2] = {0x80, cmd};
    i2c_write_blocking(i2c_default, (OLED_ADDR & OLED_WRITE_MODE), buf, 2, false);
}

void oled_send_buf(uint8_t buf[], int buflen) {
    // in horizontal addressing mode, the column address pointer auto-increments
    // and then wraps around to the next page, so we can send the entire frame
    // buffer in one gooooooo!

    // copy our frame buffer into a new buffer because we need to add the control byte
    // to the beginning

    // TODO find a more memory-efficient way to do this..
    // maybe break the data transfer into pages?
    uint8_t *temp_buf = malloc(buflen + 1);

    for (int i = 1; i < buflen + 1; i++) {
        temp_buf[i] = buf[i - 1];
    }
    // Co = 0, D/C = 1 => the driver expects data to be written to RAM
    temp_buf[0] = 0x40;
    i2c_write_blocking(i2c_default, (OLED_ADDR & OLED_WRITE_MODE), temp_buf, buflen + 1, false);

    free(temp_buf);
}

void oled_init() {
    // some of these commands are not strictly necessary as the reset
    // process defaults to some of these but they are shown here
    // to demonstrate what the initialization sequence looks like

    // some configuration values are recommended by the board manufacturer

    oled_send_cmd(OLED_SET_DISP | 0x00); // set display off

    /* memory mapping */
    oled_send_cmd(OLED_SET_MEM_ADDR); // set memory address mode
    oled_send_cmd(0x00); // horizontal addressing mode

    /* resolution and layout */
    oled_send_cmd(OLED_SET_DISP_START_LINE); // set display start line to 0

    oled_send_cmd(OLED_SET_SEG_REMAP | 0x01); // set segment re-map
    // column address 127 is mapped to SEG0

    oled_send_cmd(OLED_SET_MUX_RATIO); // set multiplex ratio
    oled_send_cmd(OLED_HEIGHT - 1); // our display is only 32 pixels high

    oled_send_cmd(OLED_SET_COM_OUT_DIR | 0x08); // set COM (common) output scan direction
    // scan from bottom up, COM[N-1] to COM0

    oled_send_cmd(OLED_SET_DISP_OFFSET); // set display offset
    oled_send_cmd(0x00); // no offset

    oled_send_cmd(OLED_SET_COM_PIN_CFG); // set COM (common) pins hardware configuration
    oled_send_cmd(0x02); // manufacturer magic number

    /* timing and driving scheme */
    oled_send_cmd(OLED_SET_DISP_CLK_DIV); // set display clock divide ratio
    oled_send_cmd(0x80); // div ratio of 1, standard freq

    oled_send_cmd(OLED_SET_PRECHARGE); // set pre-charge period
    oled_send_cmd(0xF1); // Vcc internally generated on our board

    oled_send_cmd(OLED_SET_VCOM_DESEL); // set VCOMH deselect level
    oled_send_cmd(0x30); // 0.83xVcc

    /* display */
    oled_send_cmd(OLED_SET_CONTRAST); // set contrast control
    oled_send_cmd(0xFF);

    oled_send_cmd(OLED_SET_ENTIRE_ON); // set entire display on to follow RAM content

    oled_send_cmd(OLED_SET_NORM_INV); // set normal (not inverted) display

    oled_send_cmd(OLED_SET_CHARGE_PUMP); // set charge pump
    oled_send_cmd(0x14); // Vcc internally generated on our board

    oled_send_cmd(OLED_SET_SCROLL | 0x00); // deactivate horizontal scrolling if set
    // this is necessary as memory writes will corrupt if scrolling was enabled

    oled_send_cmd(OLED_SET_DISP | 0x01); // turn display on
}

void render(uint8_t *buf, struct render_area *area) {
    // update a portion of the display with a render area
    oled_send_cmd(OLED_SET_COL_ADDR);
    oled_send_cmd(area->start_col);
    oled_send_cmd(area->end_col);

    oled_send_cmd(OLED_SET_PAGE_ADDR);
    oled_send_cmd(area->start_page);
    oled_send_cmd(area->end_page);

    oled_send_buf(buf, area->buflen);
}

#endif

int main() {
    stdio_init_all();

    // useful information for picotool
    bi_decl(bi_2pins_with_func(PICO_DEFAULT_I2C_SDA_PIN, PICO_DEFAULT_I2C_SCL_PIN, GPIO_FUNC_I2C));
    bi_decl(bi_program_description("OLED I2C example for the Raspberry Pi Pico"));

#if !defined(i2c_default) || !defined(PICO_DEFAULT_I2C_SDA_PIN) || !defined(PICO_DEFAULT_I2C_SCL_PIN)
#warning i2c / oled_i2d example requires a board with I2C pins
    puts("Default I2C pins were not defined");
#else
    printf("Hello, OLED display! Look at my raspberries..\n");

    // I2C is "open drain", pull ups to keep signal high when no data is being
    // sent
    i2c_init(i2c_default, 400 * 1000);
    gpio_set_function(PICO_DEFAULT_I2C_SDA_PIN, GPIO_FUNC_I2C);
    gpio_set_function(PICO_DEFAULT_I2C_SCL_PIN, GPIO_FUNC_I2C);
    gpio_pull_up(PICO_DEFAULT_I2C_SDA_PIN);
    gpio_pull_up(PICO_DEFAULT_I2C_SCL_PIN);

    // run through the complete initialization process
    oled_init();

    // initialize render area for entire frame (128 pixels by 4 pages)
    struct render_area frame_area = {start_col: 0, end_col : OLED_WIDTH - 1, start_page : 0, end_page : OLED_NUM_PAGES -
                                                                                                        1};
    calc_render_area_buflen(&frame_area);

    // zero the entire display
    uint8_t buf[OLED_BUF_LEN];
    fill(buf, 0x00);
    render(buf, &frame_area);

    // intro sequence: flash the screen 3 times
    for (int i = 0; i < 3; i++) {
        oled_send_cmd(0xA5); // ignore RAM, all pixels on
        sleep_ms(500);
        oled_send_cmd(0xA4); // go back to following RAM
        sleep_ms(500);
    }

    // render 3 cute little raspberries
    struct render_area area = {start_col: 0, end_col : IMG_WIDTH - 1, start_page : 0, end_page : OLED_NUM_PAGES - 1};
    calc_render_area_buflen(&area);
    render(raspberry26x32, &area);
    for (int i = 1; i < 3; i++) {
        uint8_t offset = 5 + IMG_WIDTH; // 5px padding
        area.start_col += offset;
        area.end_col += offset;
        render(raspberry26x32, &area);
    }

    // configure horizontal scrolling
    oled_send_cmd(OLED_SET_HORIZ_SCROLL | 0x00);
    oled_send_cmd(0x00); // dummy byte
    oled_send_cmd(0x00); // start page 0
    oled_send_cmd(0x00); // time interval
    oled_send_cmd(0x03); // end page 3
    oled_send_cmd(0x00); // dummy byte
    oled_send_cmd(0xFF); // dummy byte

    // let's goooo!
    oled_send_cmd(OLED_SET_SCROLL | 0x01);

#endif
    return 0;
}