122 lines
3.6 KiB
Rust
122 lines
3.6 KiB
Rust
#![no_std]
|
|
#![no_main]
|
|
|
|
use defmt::{panic, *};
|
|
use embassy_executor::Spawner;
|
|
use embassy_futures::join::join;
|
|
use embassy_stm32::gpio::{Level, Output, Speed};
|
|
use embassy_stm32::time::Hertz;
|
|
use embassy_stm32::usb::{Driver, Instance};
|
|
use embassy_stm32::{bind_interrupts, peripherals, usb, Config};
|
|
use embassy_time::Timer;
|
|
use embassy_usb::class::cdc_acm::{CdcAcmClass, State};
|
|
use embassy_usb::driver::EndpointError;
|
|
use embassy_usb::Builder;
|
|
use {defmt_rtt as _, panic_probe as _};
|
|
|
|
bind_interrupts!(struct Irqs {
|
|
USB_LP_CAN1_RX0 => usb::InterruptHandler<peripherals::USB>;
|
|
});
|
|
|
|
#[embassy_executor::main]
|
|
async fn main(_spawner: Spawner) {
|
|
let mut config = Config::default();
|
|
{
|
|
use embassy_stm32::rcc::*;
|
|
config.rcc.hse = Some(Hse {
|
|
freq: Hertz(8_000_000),
|
|
// Oscillator for bluepill, Bypass for nucleos.
|
|
mode: HseMode::Oscillator,
|
|
});
|
|
config.rcc.pll = Some(Pll {
|
|
src: PllSource::HSE,
|
|
prediv: PllPreDiv::DIV1,
|
|
mul: PllMul::MUL9,
|
|
});
|
|
config.rcc.sys = Sysclk::PLL1_P;
|
|
config.rcc.ahb_pre = AHBPrescaler::DIV1;
|
|
config.rcc.apb1_pre = APBPrescaler::DIV2;
|
|
config.rcc.apb2_pre = APBPrescaler::DIV1;
|
|
}
|
|
let mut p = embassy_stm32::init(config);
|
|
|
|
info!("Hello World!");
|
|
|
|
{
|
|
// BluePill board has a pull-up resistor on the D+ line.
|
|
// Pull the D+ pin down to send a RESET condition to the USB bus.
|
|
// This forced reset is needed only for development, without it host
|
|
// will not reset your device when you upload new firmware.
|
|
let _dp = Output::new(&mut p.PA12, Level::Low, Speed::Low);
|
|
Timer::after_millis(10).await;
|
|
}
|
|
|
|
// Create the driver, from the HAL.
|
|
let driver = Driver::new(p.USB, Irqs, p.PA12, p.PA11);
|
|
|
|
// Create embassy-usb Config
|
|
let config = embassy_usb::Config::new(0xc0de, 0xcafe);
|
|
//config.max_packet_size_0 = 64;
|
|
|
|
// Create embassy-usb DeviceBuilder using the driver and config.
|
|
// It needs some buffers for building the descriptors.
|
|
let mut config_descriptor = [0; 256];
|
|
let mut bos_descriptor = [0; 256];
|
|
let mut control_buf = [0; 7];
|
|
|
|
let mut state = State::new();
|
|
|
|
let mut builder = Builder::new(
|
|
driver,
|
|
config,
|
|
&mut config_descriptor,
|
|
&mut bos_descriptor,
|
|
&mut [], // no msos descriptors
|
|
&mut control_buf,
|
|
);
|
|
|
|
// Create classes on the builder.
|
|
let mut class = CdcAcmClass::new(&mut builder, &mut state, 64);
|
|
|
|
// Build the builder.
|
|
let mut usb = builder.build();
|
|
|
|
// Run the USB device.
|
|
let usb_fut = usb.run();
|
|
|
|
// Do stuff with the class!
|
|
let echo_fut = async {
|
|
loop {
|
|
class.wait_connection().await;
|
|
info!("Connected");
|
|
let _ = echo(&mut class).await;
|
|
info!("Disconnected");
|
|
}
|
|
};
|
|
|
|
// Run everything concurrently.
|
|
// If we had made everything `'static` above instead, we could do this using separate tasks instead.
|
|
join(usb_fut, echo_fut).await;
|
|
}
|
|
|
|
struct Disconnected {}
|
|
|
|
impl From<EndpointError> for Disconnected {
|
|
fn from(val: EndpointError) -> Self {
|
|
match val {
|
|
EndpointError::BufferOverflow => panic!("Buffer overflow"),
|
|
EndpointError::Disabled => Disconnected {},
|
|
}
|
|
}
|
|
}
|
|
|
|
async fn echo<'d, T: Instance + 'd>(class: &mut CdcAcmClass<'d, Driver<'d, T>>) -> Result<(), Disconnected> {
|
|
let mut buf = [0; 64];
|
|
loop {
|
|
let n = class.read_packet(&mut buf).await?;
|
|
let data = &buf[..n];
|
|
info!("data: {:x}", data);
|
|
class.write_packet(data).await?;
|
|
}
|
|
}
|