changelog fixes

cyw43/CHANGELOG.md

@@ -9,8 +9,10 @@ and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0
 
 ## 0.3.0 - 2025-01-05
 
-- Update embassy-time to 0.4.0
+- Update `embassy-time` to 0.4.0
-- Update embassy-rp to 0.3.0
+- Add Bluetooth support.
+- Add WPA3 support.
+- Expand wifi security configuration options.
 
 ## 0.2.0 - 2024-08-05
 

cyw43/README.md

@@ -1,27 +1,36 @@
 # cyw43
 
-Rust driver for the CYW43439 wifi chip, used in the Raspberry Pi Pico W. Implementation based on [Infineon/wifi-host-driver](https://github.com/Infineon/wifi-host-driver).
+Rust driver for the CYW43439 wifi+bluetooth chip. Implementation based on [Infineon/wifi-host-driver](https://github.com/Infineon/wifi-host-driver).
 
-## Current status
+Works on the following boards:
+
+- Raspberry Pi Pico W (RP2040)
+- Raspberry Pi Pico 2 W (RP2350A)
+- Pimoroni Pico Plus 2 W (RP2350B)
+- Any board with Raspberry Pi RM2 radio module.
+- Any board with the CYW43439 chip, and possibly others if the protocol is similar enough.
+
+## Features
 
 Working:
 
-- Station mode (joining an AP).
+- WiFi support
-- AP mode (creating an AP)
+    - Station mode (joining an AP).
-- Scanning
+    - AP mode (creating an AP)
-- Sending and receiving Ethernet frames.
+    - Scanning
-- Using the default MAC address.
+    - Sending and receiving Ethernet frames.
-- [`embassy-net`](https://embassy.dev) integration.
+    - Using the default MAC address.
-- RP2040 PIO driver for the nonstandard half-duplex SPI used in the Pico W.
+    - [`embassy-net`](https://embassy.dev) integration.
-- Using IRQ for device events
+    - RP2040 PIO driver for the nonstandard half-duplex SPI used in the Pico W.
-- GPIO support (for LED on the Pico W)
+    - Using IRQ for device events, no busy polling.
+    - GPIO support (for LED on the Pico W).
+- Bluetooth support
+    - Bluetooth Classic + LE HCI commands.
+    - Concurrent operation with WiFi.
+    - Implements the [bt-hci](https://crates.io/crates/bt-hci) controller traits.
+    - Works with the [TrouBLE](https://github.com/embassy-rs/trouble) bluetooth LE stack. Check its repo for examples using `cyw43`.
 
-TODO:
+## Running the WiFi examples
-
-- Setting a custom MAC address.
-- Bus sleep (for power consumption optimization)
-
-## Running the examples
 
 - Install `probe-rs` following the instructions at <https://probe.rs>.
 - `cd examples/rp`

embassy-nrf/CHANGELOG.md

@@ -11,7 +11,7 @@ and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0
 
 - Updated `embassy-time` to v0.4
 - Add basic nrf54 support
-- Switch to use nrf-pac chiptool based PAC
+- Switch to use `nrf-pac` chiptool-based PAC
 - Fix bug where timer alarm was not scheduled if interrupted
 - Add RESET operations helpers for nrf5340
 - Allow debug access from firmware for nrf54l

embassy-rp/CHANGELOG.md

@@ -9,10 +9,12 @@ and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0
 
 ## 0.3.0 - 2025-01-05
 
+- Updated `embassy-time` to v0.4
 - Initial rp235x support
 - Setup timer0 tick when initializing clocks
 - Allow separate control of duty cycle for each channel in a pwm slice by splitting the Pwm driver.
 - Implement `embedded_io::Write` for Uart<'d, T: Instance, Blocking> and UartTx<'d, T: Instance, Blocking>
+- Add `set_pullup()` to OutputOpenDrain.
 
 ## 0.2.0 - 2024-08-05